Skip to Content

Can a new mixer drum go on the truck you already own? A chassis guide

November 17, 2026 by

If your truck is sound but its drum is worn through, you do not have to replace the whole mixer. A new Stetter drum can be mounted on a chassis you already own, provided the frame is long enough, the axles can carry the load and the engine can drive it. This guide shows how to check.

4 to 12 m³drum sizes we supply for mounting
3 checksframe length, axle load, engine and PTO
4 detailswe need from you to confirm the fit
1 workshopmounting done in our own workshop

Why keep the truck and change the drum

A mixer drum wears from the inside. The spirals thin, the shell thins, and discharge slows long before the truck under it is finished. Many mixers on Philippine roads also started life elsewhere, on chassis whose engines and frames still have years in them.

  • You pay for a mixer, not for another truck. The chassis you already own keeps working.
  • The truck comes back with a new drum. New spirals with protected wear edges mix properly and empty quickly again.
  • Your drivers and mechanics stay on a truck they know. No new chassis to learn or stock parts for.
  • The drum is supported locally. Parts and drum servicing come from the same company that mounted it.

The three things that decide whether it fits

  1. Frame lengthThe drum, its subframe and the discharge trestle need a clear run of frame behind the cab. This is the loading span.
  2. Axle loadConcrete weighs about 2.4 tonnes per cubic meter. The axles must be rated for the mixer plus a full drum.
  3. Engine and PTOThe drum is turned hydraulically from the truck engine through a power take-off. The engine needs enough power, and the PTO must be in a usable position.
Loading span: clear frame behind the cabWheelbaseAxle spacingRear overhang
The measurements that matter. Loading span runs from the back of the cab to the end of the frame. Rear overhang is the frame behind the last axle.

What each drum size needs from a chassis

Find the drum size you want, then compare the row with your truck.

DrumDriveLoading spanWheelbaseRear overhangEngine, at leastMixer weight
AM 44x23,700 mm3,600 mm1,000 mm180 hp3,400 kg
AM 6 and AM 76x44,700 to 5,000 mm3,300 + 1,350 mm1,000 mm180 hp3,450 kg
AM 86x45,600 mm3,800 + 1,350 mm1,300 mm230 hp3,950 kg
AM 96x45,900 mm3,800 + 1,350 mm1,300 mm280 hp4,200 kg
AM 108x46,200 mm1,800 + 3,000 + 1,350 mm1,500 mm280 hp4,400 kg
AM 128x47,300 mm1,800 + 3,600 + 1,350 mm1,500 mm300 hp4,900 kg

Manufacturer guide values for a day-cab chassis. The loading span depends on where the PTO sits, so it is confirmed for each truck. Wheelbase is given axle to axle.

Do the weight sum before anything else. A 6 m³ drum carries about 14.4 tonnes of concrete. Add about 3.45 tonnes of mixer, plus water, and the chassis must legally carry around 18 tonnes on top of its own weight.

What to send us

With these four details we can tell you whether the drum fits, and which size suits the truck.

  1. A chassis drawing, as a CAD or DXF file if you can get one from the truck maker. If not, the measurements below.
  2. Unladen axle weights, front and rear, with no body on the truck.
  3. Permissible axle loads, front and rear, from the vehicle plate or registration.
  4. PTO details: where it is, and which way it turns when you look from the rear of the truck.

No drawing? Measure these

  • Wheelbase, and the spacing between the rear axles
  • Rear overhang, from the last axle to the end of the frame
  • Loading span, from the back of the cab to the end of the frame
  • Front axle to the back of the cab
  • Frame width and the height of the frame rail
  • PTO position: distance back, height from the top of the frame, and any offset from the center line
  • Rear drive (6x2 or 6x4) and the type of rear suspension
  • Electrical system, 12 V or 24 V

Photos of the truck from the side, of the frame behind the cab and of the PTO help as well.

An AM 6 on a customer's Hino

This is a recent job in our workshop: a 6 m³ Stetter AM 6 mounted on a Hino 6x4 that the customer already owned. The truck came in with its previous drum and went out with a new one.

A Hino 6x4 mixer truck before its drum was replaced
The truck as it arrived, with its previous drum.
A new Stetter AM 6 mixer drum on its subframe before mounting
The new AM 6 on its subframe, ready to mount.
A Stetter AM 6 drum being lowered onto a Hino 6x4 chassis in the workshop
Lowering the drum onto the chassis.
Technicians fitting a Stetter mixer drum to a truck chassis
Fixing the subframe and connecting the drive.
A Stetter AM 6 mixer drum mounted on a Hino 6x4 chassis, side view
Mounted on the chassis, before final finishing.

When the truck does not qualify

Some trucks are too short, too light on the axles or too low on power for the drum the owner wants. There are two ways forward.

  • A smaller drum. A chassis that cannot carry 8 m³ may carry 6 m³ safely and legally.
  • A complete unit. We also supply Stetter mixers already mounted on a new truck, with one company responsible for both. See the transit mixers page.

For 4 m³ work, the AM 4 SHC has its own drum engine, so it needs no PTO from the truck at all.

Want to know if your truck qualifies?

Send us the make, model and the measurements above.

Send your chassis details

See the Stetter transit mixers

in Blog
Rod side or piston side: how one Schwing pump gives you high output or high pressure
Message usClose
Schwing Stetter PhilippinesChat with us on Messenger

Hello. Tell us which equipment or parts you need, and where your project is. We will reply on Messenger.

Opens Messenger with your message ready to send.