Skip to Content

Pan mixer or twin-shaft mixer: what is inside your batching plant, and why it matters

November 17, 2026 by

A batching plant weighs the ingredients. The mixer is what turns them into concrete, and on a ready-mix plant it has about 30 seconds a batch to do it. Stetter builds two kinds of mixer. Which one your plant carries decides what concrete you can make, and how fast.

30 smixing time behind a twin-shaft plant's rated output
0.5 to 2.25 m³batch sizes of Stetter pan mixers
1.25 to 4.0 m³batch sizes of Stetter twin-shaft mixers
160 mmlargest aggregate, with the coarse-grain option

Why the mixer matters as much as the scales

Concrete is strong only where every stone and every grain of sand is coated in cement paste. A batch can be weighed to the kilo and still come out with dry pockets, lumps of cement and uneven strength if the mixer does not finish the job.

Both Stetter mixers are compulsory mixers. A drum tumbles the material and waits for gravity to blend it. A compulsory mixer drives its tools through the material and forces it to move. That is why a batching plant can turn out a finished batch in well under a minute.

Pan mixer, seen from above: a round pan with arms turning on a vertical shaft.
Twin-shaft mixer, seen from above: a trough with two shafts turning in opposite directions.

The pan mixer

A pan mixer is a round, flat pan with a rotor turning on a vertical shaft in the middle. The rotor carries spring-mounted mixing arms. Scrapers run along the inner and outer walls and push the material back into the path of the arms, so nothing sits still at the edge.

  • Intense mixing. The material only has a short way to travel, sideways and up and down, before it is fully blended.
  • Short mixing time. Short paths mean the batch is uniform quickly.
  • Low energy use. The mixer reaches a uniform batch with little energy put in.
  • Accessible components. The pan is open from above. The floor and wall linings can be exchanged, and the wall wear plates can be turned over and used again.
  • Quality concrete in every slump range. It handles stiff and flowing mixes alike, and its sliding gates empty the pan completely, so little of the last batch stays behind when you change recipes.
Stetter CP 18 compact batching plant with its round pan mixer under the frame
A Stetter CP 18 on a project site in the Philippines. The round green vessel under the frame is its pan mixer.

You find pan mixers in the compact and smaller mobile plants: the CP 18, CP 30 and M1. Stetter pan mixers take aggregate up to 80 mm round or 63 mm crushed. The M1 is also built as the M1T, with a twin-shaft mixer in place of the pan. For precast work, the CP 30 can also be supplied with a turbo pan or planetary pan mixer.

The twin-shaft mixer

A twin-shaft mixer is a trough with two horizontal shafts turning in opposite directions. The mixing arms sit on the shafts in a spiral, so the two shafts throw the material toward each other in the middle of the trough while moving it along its length.

  • Thorough mixing at volume. Batches run from 1.25 to 4.0 m³, which is what a ready-mix plant needs to keep trucks moving.
  • Wide range of applications. From everyday ready-mix to mass concrete for dams.
  • Low wear. The shafts turn slowly, and the trough floor is lined with 20 mm chilled cast iron tiles.
  • Very large aggregate. Up to 80 mm as standard on most sizes, and up to 160 mm with the coarse-grain mixing unit.
  • Short discharge. A gate running between the two shafts empties the trough fast, and its opening can be set in steps to match what the transit mixer can take.

You find twin-shaft mixers in the larger plants: the T models of the M series such as the M1T, the M 2.5 mobile plant, and the H and HN horizontal plants.

Side by side

Pan mixerTwin-shaft mixer
ShapeRound pan, one vertical shaftTrough, two horizontal shafts
Stetter batch sizes0.5 to 2.25 m³1.25 to 4.0 m³
Largest aggregate80 mm round, 63 mm crushed80 mm, or 160 mm with the coarse-grain unit
DischargeSliding gates in the pan floorGate between the shafts, opening adjustable
Strongest atSmaller batches, frequent recipe changes, precastHigh hourly output, ready-mix supply, mass concrete
Found inCP 18, CP 30, M1M series T models (such as the M1T), M 2.5, H and HN series

Which one do you need?

  1. A project siteBatching for your own pours, up to about 56 m³ an hour: a compact or mobile plant with a pan mixer.
  2. A ready-mix businessLoading transit mixers all day: a twin-shaft plant, for its batch size and fast discharge.
  3. Mass concreteDams and heavy foundations with aggregate above 80 mm: a twin-shaft mixer with the coarse-grain unit.
  4. PrecastStiff mixes and many recipe changes a day: a pan mixer.
On most plants you do not pick the mixer separately. It comes with the plant size. Start from the concrete you need and the volume you need each hour, and the mixer follows.

Not sure which plant fits your concrete?

Tell us your mix, your aggregate and your hourly volume.

Request a quotation

See the full range of Stetter batching plants

Concrete where ready-mix trucks cannot reach: how a self-loading mixer works
Message usClose
Schwing Stetter PhilippinesChat with us on Messenger

Hello. Tell us which equipment or parts you need, and where your project is. We will reply on Messenger.

Opens Messenger with your message ready to send.