Skip to Content

How a twin-shaft mixer works

November 19, 2026 by
Schwing Stetter Philippines

The larger Schwing Stetter plants mix with two horizontal shafts in one trough. The design mixes fast, wears in few places, and can restart with a full load. This is how it works, how a new one is commissioned, and what its common symptoms mean.

Who this is for: plant owners, managers and trained operators. Commissioning and adjustments are carried out by trained service personnel. Owners can use this guide to understand what is done and what to keep on record.
15 sto reach 85% mixed
30 sto reach 95% mixed
3 mmgap between the mixing tools and the trough
30%longer tile life claimed for rhombus tiles over rectangular ones

How it mixes

Each shaft is a hexagonal bar with mixing arms set around it in a spiral. As the shafts turn, the arms push material along the shaft and around it at once, so it travels a three-dimensional path. Where the two mixing circles cross, material from both sides meets, and that overlap is what brings the mix together so quickly.

Turbulent zone
Two shafts, two mixing circles, one overlap. Material is thrown across the middle from both sides, which is where the mixing is most intense.
After 15 s85%After 30 s95%
How quickly a twin-shaft mixer reaches a uniform mix, as given by the manufacturer.

Built to wear in few places

  • Only about 30% of each mixing tool's rotation is exposed to wear on the trough floor.
  • Only three to four rows of bottom tiles take the wear, and the tiles are identical, so they are simple to replace.
  • The mixing arms are modular special castings. One arm can be replaced without the rest.
  • The shaft bearings are separate from the shaft seals. If a seal fails, the bearing behind it is not damaged, and the seal is easy to reach.

The drive

  • Worm gear reducers with an efficiency above 92%. They absorb the shock of sudden feeding or a restart under full load.
  • A synchronous coupling between the two gear units keeps the shafts in step. It is elastic and maintenance free.
  • A torque support lets the drive hang freely, keeps the coupling aligned and takes load off the gearbox bearings.
  • Central grease lubrication feeds the four shaft seals while the mixer runs.

The discharge door

The door is worked by two or four pneumatic cylinders, depending on mixer size, with hydraulic cylinders as an option. It opens in stages, so a transit mixer can be fed at the rate it can take. The standard door has a half-open position; the large door has two intermediate positions.

Commissioning a new mixer

  1. Check the installation. Casing level, feed and discharge devices fitted, limit switches fitted on the maintenance doors, guards on all rotating parts.
  2. Check the mixer itself. About 3 mm between the mixing tools and the trough, shafts turning freely, V-belt tension, gearbox oil level, no foreign material in the trough.
  3. Run it empty for 20 to 30 minutes. Listen for abnormal noise and test the emergency stop and the limit switches. On a star-delta drive, the switch from star to delta takes 2.5 to 3 seconds.
  4. Check the door. Air pressure at 8 bar, cylinders cycled several times, limit switches reset if needed, grease showing at the axial face seals.
  5. Break it in. Two batches at half the nominal filling and a third at nominal filling, 60 seconds each.
  6. Go gently for the first ten mixes. Use fluid concrete with a maximum particle size of 4 mm.

Feeding and running

  • Feed in a fixed, timed order. Aggregates first, water one to two seconds later, and the binder once 80 to 90% of the aggregate is in.
  • Keep mixing time short. Mixing for more than two minutes increases wear and heats the drive.
  • Watch the gear unit temperature. In continuous work it runs 25 to 45°C above ambient and must not exceed 90°C.
  • If the mixer stops with a load in it, open the discharge door and empty the trough. In a power failure the door can still be opened with the emergency controls on its solenoid valves, using the air left in the system.

What the symptoms mean

SymptomProbable causeAction
Mixer does not start when empty, on a two-motor driveMotors turning in opposite directionsReverse one motor and confirm the shafts rotate correctly
Mixer stops under loadLoose V-belts, low oil in the hydraulic coupling, or an electrical faultRetension the belts, check the oil filling, check supply, fuses and voltage
Discharge door does not openAir supply below 8 bar, or stones jammed at the doorRaise the line pressure; free the door
Deposits on shafts, tools and coverCement called too early or water too lateCorrect the feeding sequence
Loud mixing noiseBlade gap too largeReadjust the lateral and central blades
Excessive tool wearBlade gap or door sealing gap too large, or mixing time too longReadjust the blades, reset the sealing ledges, shorten the mixing time
Cement slurry leaking at the shaft sealAxial face seal damaged by lack of lubricationReplace the axial face seal
A running noise from the gear units when idling can mean bearing or gear damage starting. That is the point to stop and call us, not to keep batching.

Lubrication

The worm gear reducers take gear oil VG 460: 70 liters on the mixer in the manufacturer's list, first changed at 500 hours and then every 2,000 hours. EP 2 grease is used on all bearings, seals and grease nipples. After the mixer has been cleaned, grease the shaft seals by hand. The rest is in our lubrication guide.

These figures come from the manufacturer's training material for its twin-shaft mixers. Quantities and settings vary with mixer size, so the manual supplied with your mixer comes first.

Running a twin-shaft plant?

Tell us the plant model and what the mixer is doing, and we will help you work out what it needs.

Talk to us about your mixer
The 51-point weekly batching plant check
Message usClose
Schwing Stetter PhilippinesChat with us on Messenger

Hello. Tell us which equipment or parts you need, and where your project is. We will reply on Messenger.

Opens Messenger with your message ready to send.