Skip to Content

Aggregate size and mix design: how a batching plant turns the right stone into consistent concrete

November 18, 2026 by

Sand and stone make up most of every cubic meter of concrete, and they are the cheapest part of it. The size of that stone, and how well the sizes are blended, decides how much cement you need, how the concrete handles and whether it reaches its strength. A batching plant cannot change the stone you buy. What it can do is keep the sizes apart, weigh each one, and put the same blend into every batch.

4 to 6aggregate sizes kept separate, depending on the plant
40 mmlargest stone for the pan-mixer M series plants
63 mmlargest stone for the twin-shaft M series plants
Stetter CP 18 batching plant with its aggregate feed conveyor carrying stone up to the storage bins
Aggregate on its way into a CP 18. What happens between this belt and the mixer decides how consistent the concrete is.

Why stone size changes the mix

Think of a box filled with large stones. The gaps between them have to be filled with smaller stone, then sand, then cement paste. The better the sizes fit together, the less paste is needed to fill what is left, and paste is where the cement cost sits.

  • Larger stone needs less cement. For the same strength and workability, a mix with larger stone has less surface to coat and needs less water and cement.
  • Smaller stone goes where large stone cannot. Thin sections, tight reinforcement and pump lines all limit how big the stone can be.
  • A blend beats a single size. Two stone sizes with a well-graded sand pack more tightly than one size alone, which gives a denser, stronger concrete.
  • Sand carries water. Wet sand brings water into the batch that nobody measured, and the water-cement ratio drifts with it.
A common rule in concrete practice: the largest stone should be no more than one fifth of the narrowest part of the form, one third of a slab's depth, and three quarters of the clear gap between reinforcing bars. For pumped concrete it also has to suit the pipeline. Your structural engineer and local code have the last word.
DRAWN TO SCALE How big a stone each mixer will take 3/8 in 9.5 mm Fine stone 3/4 in 19 mm Common stone 40 mm Pan mixer limit 45 mm Planetary mixer limit 63 mm Twin-shaft mixer limit Sizes most mixes use Largest stone by mixer type, Stetter M series

What the plant does with it

It keeps each size in its own bin

A mix design that calls for two stone sizes and two sands needs four separate stores. The CP 18 has four aggregate compartments. The CP 30 holds four sizes with a scraper or compartment batcher and up to six with an in-line silo. On the M series, the compartment batcher has four chambers and the in-line silo has five bins with ten batching gates.

It weighs each size, every batch

The sizes are not fed by volume or by loader bucket. Each one is discharged through its own gate onto the scale until its target weight is reached, then the next. The scale on a CP 18 weighs up to 700 kg of aggregate per batch, the CP 30 up to 1,250 kg and the M 2.5 up to 6,250 kg.

It corrects for what changes during the day

The plant control system has settings for weighing tolerance, a coarse then fine feed so each gate closes on target, the material still falling when a gate shuts, and the moisture in the aggregate. These are what keep batch 200 the same as batch 1 when the sand pile gets wetter after rain.

It mixes what the recipe asked for

Cement and water are weighed separately, on their own scales, and everything meets in the mixer. The mixer type sets the largest stone the plant can take: 40 mm for the pan mixers on the smaller M series plants, 45 mm for the planetary mixer, and 63 mm for the twin-shaft mixers from the M 1.25 upward.

A CP 30 with a scraper: aggregates are stockpiled on the ground by size and pulled to the weighing gates as each batch needs them.

What that is worth on site

  • For a contractor batching for its own project: the mix the engineer approved is the mix that goes into the structure. Fewer failed cylinders, less cement added "to be safe", and no arguments with a supplier over what was delivered.
  • For a ready-mix producer: every truck of a given grade is the same, whoever is on shift. You can run more mix designs from the same bins, and the batch record shows the customer exactly what was weighed.

Which plant for which job

PlantOutputAggregate sizesMixerSuits
CP 1818 m³/hr4PanA contractor's own projects, housing, precast and pipe works
CP 3030 m³/hr4, or up to 6 with in-line siloPan or planetaryLarger projects and small ready-mix supply; scraper version stores the most aggregate on the ground
M 156 m³/hr4, or 5 with in-line siloPlanetary, or twin-shaft on the M 1TMobile plant for infrastructure jobs that move, and for growing ready-mix suppliers
M 2.5112 m³/hr4, or 5 with in-line siloTwin-shaft, stone up to 63 mmReady-mix production and large pours, including mass concrete with big stone

Related

Not sure which plant fits your mixes?

Tell us your aggregate sizes, your grades of concrete and how much you pour in a day.

Ask which plant fits
in Blog
Two CP 18 plants, 4,500 concrete pipes: a small batching plant on a production line
Message usClose
Schwing Stetter PhilippinesChat with us on Messenger

Hello. Tell us which equipment or parts you need, and where your project is. We will reply on Messenger.

Opens Messenger with your message ready to send.