A concrete pump pushes a heavy, abrasive material through steel pipe at high pressure. Almost every serious accident comes from the same few moments: opening a line that is still under pressure, a hand where a moving part is, or an end hose that whips. These are the rules Schwing Stetter gives pump crews, grouped by the part of the job they belong to.
Setting up
- Wear the protective equipment, including hearing protection.
- Pump on its stabilizers. The pump always rests on its stabilizers while pumping, on firm ground. A machine can sink into soft ground; never work under one there.
- Barricade the pumping area and keep it drained so water and slurry do not collect.
- Agree the signals. The operator and the people at the pipeline and the placing end use the same hand signals, for pumping and for cleaning.
- Anchor the line. Fix the first 20 m of pipeline and the start of the vertical run properly.
The pipeline
Laying the line takes time. Get the pump to site early enough to do it properly.
- Newest pipe nearest the pump. Concrete pressure is highest at the pump end.
- Measure wall thickness with a gauge. A pipe worn by more than half its wall does not go back in the line. Above 180 bar operating pressure, the pipe at the pump end should be at least 3 mm thick.
- No hammering, no welding. Dents wear through quickly. Welded, fabricated or reconditioned pipes do not belong in a delivery line.
- Support it rigidly, with brackets close to the couplings so the joints carry no weight or movement.
- Secure every coupling after fitting, and allow no slurry to leak at the clamps. A leaking joint also causes blockages.
The end hose
- Do not hold it before concrete arrives. It can whip.
- Use the prescribed length. A longer hose bends too far, blocks, and whips harder.
- Never kink it, and never bend it past 30 degrees. A kink can straighten violently under pressure.
- Never beat it with a hammer or anything else. The reinforcement can be damaged where you cannot see it, and the hose can burst the next time it is under pressure.
- Inspect it before every use: no frays, no exposed reinforcement, inner and outer liner sound, no deep cracks at the coupling end.
Hands and feet away from moving parts
- Never put a hand in the water box while pumping.
- Never stand on the hopper grill, and never remove it while the pump or agitator is running.
- Never clean the valve or gates by hand in pumping mode. When someone has to work there, a second person stands at the forward and reverse control so that nobody operates it.
- For maintenance, the ignition key comes out and stays in the operator's pocket. For repairs, disconnect the battery and lock the controls in neutral.
- Supervise helpers at the hopper, at the water box and while a blockage is being cleared.
When the line blocks
A blockage raises the risk of an accident. Find the cause and clear it in this order.
- Reverse at once. Switch to reverse pumping for 2 to 3 strokes.
- Try forward again.
- If it is still blocked, reverse again to take the pressure off the line.
- Switch the pump off.
- Take out the blocked section and clean it.
Why lines block in the first place is covered in what makes concrete pumpable.
Cleaning out
The pour is finished and everyone is tired, which is when accidents happen.
- Empty the delivery line and the hopper completely.
- If the line is cleaned with compressed air, take the end hose off first.
- Fit a ball catcher or trap basket at the end of the line before any air is applied. Blowing out a line with compressed air is very hazardous without one.
The full procedure is in how to clean and inspect a concrete pipeline.
Hydraulics, fuel and batteries
- Hydraulic pressure. Stop the engine and work the controls to release trapped pressure before a hose is disconnected, and make sure the engine cannot be started while hoses are open.
- Looking for a leak. Never with your fingers or your face. A fine jet of hydraulic oil can go through skin. Hold a piece of cardboard near the suspected leak and look at the cardboard. If oil does penetrate the skin, get medical help immediately.
- Hoses. Replace any hose with damaged end fittings, a chafed or ballooned cover, or a kink or crush.
- Fuel. Refuel with the engine stopped, and no smoking or open flame near the machine.
- Batteries. They give off explosive gas, so keep sparks and flames away. Connect the earth lead last and disconnect it first.
- Fire. Do not use water on a machine fire. Use a carbon dioxide, dry chemical or foam extinguisher, and have the extinguisher on the machine checked regularly.
- Repairs. No unapproved modifications, no welding on cast parts, and no repair work by anyone who has not been trained for it.
Want your crew trained on the pump?
Tell us which pump you run and how many operators you have, and we will tell you what training we can arrange.
Ask about operator training