Skip to Content

How to clean and inspect a concrete pipeline

November 17, 2026 by

The pour is not finished until the line is clean. Concrete left in a pipe sets, narrows the bore and becomes the next job's blockage. Cleaning straight away, and checking the pipe walls regularly, is what keeps a pipeline earning for years.

4 methodsfor emptying a delivery line
At onceclean before the concrete stiffens
Every sealchecked, and replaced if damaged
30 barof pressure rating for each mm of wall

Watch: cleaning a concrete pipeline

Cleaning the delivery line after a pour.

Clean at once, and clean the joints too

  • Wash pipe sections with a water jet as soon as they come off. Fresh concrete rinses out. Set concrete has to be chipped out.
  • Clean the couplings and their seals. Grit left in a coupling stops it sealing on the next job, and a leaking joint is how blockages start.
  • Replace damaged seals now. It is the cheapest part on the line, and the most common cause of lost paste.
A delivery pipe being opened at a coupling during cleaning
Opening the line at a coupling. Every joint that is opened gets its seal cleaned and checked.

Four ways to empty the line

The concrete can be pushed out toward the pouring point, or back toward the pump. Which way, and with what, depends on the job.

  1. Compressed airA cleaning ball is blown through the line with air. Fast, and it needs no water at the far end.
  2. Reverse pumpingThe pump is run in reverse to draw concrete back into the hopper.
  3. Water wash-out for long linesFor very long or horizontal lines, the pump pushes water behind a cleaning plug. See the steps below.
  4. Free flowOn a vertical line, the concrete is allowed to run back down under its own weight.
Compressed air stores a great deal of energy. Use it only with a trained crew, a catch basket on the open end of the line, and nobody standing at the discharge.

Washing out a long line with water

  1. Prepare the cleaning plug, often called a go-devil.
  2. Clear the first few feet of pipe at the pump end and insert the plug.
  3. Connect a high-pressure hose between the pump and the pipeline.
  4. Fill the hopper with water and pump. The water drives the plug, and the plug drives the concrete out ahead of it.

The concrete pushed out is still usable at the pour, so a wash-out done well wastes very little.

The open end of a delivery pipe laid on timber supports
The open end of a line after cleaning.

Inspect the wall thickness

Concrete wears steel. A delivery pipe gets thinner from the inside with every cubic meter, and a thinner wall holds less pressure. You cannot see this wear from outside, so it is measured with an ultrasonic thickness gauge held against the pipe.

An ultrasonic thickness gauge measuring the wall of a delivery pipe
An ultrasonic gauge reads the remaining wall thickness from the outside.

For a standard 139.7 x 7.1 mm pipe, the pressure the wall can take falls in step with its thickness, by about 30 bar for each millimeter.

0123456704080120160200Remaining wall thickness, mmConcrete pressure, barPipe 139.7 x 7.1 mm
Schwing Stetter's recommendation for a 139.7 x 7.1 mm pipe. A new 7 mm wall is good for about 210 bar. Worn to 4 mm, the same pipe is good for about 120 bar.

What to do with the readings

  • Measure where wear is worst: the pipes nearest the pump, the outside of every bend, and the bottom of horizontal runs.
  • Compare each reading with the pressure your job needs. Our pump sizing guide shows how to work that out.
  • Move worn pipes down the line. Pressure is highest at the pump and falls toward the end, so a pipe too thin for the first run may still be safe near the pour.
  • Retire a pipe before it is below what the job needs, not after it bursts.

Need pipes, couplings or seals?

Tell us the line diameter and what you need replaced.

Ask about parts

Parts and service

in Blog
How to lay and support a concrete delivery line
Message usClose
Schwing Stetter PhilippinesChat with us on Messenger

Hello. Tell us which equipment or parts you need, and where your project is. We will reply on Messenger.

Opens Messenger with your message ready to send.